Fit Approval
Virtual and physical fit sessions.
What really happens at this stage
Fit approval is the checkpoint where a garment's dimensions, ease, and silhouette are confirmed against the design intent, combining virtual fit review in 3D software with physical fit sessions on a fit model, mannequin, or live model. Virtual fit sessions let designers and merchandisers rotate a digital avatar through standard poses to catch obvious proportion or drape problems early, but virtual review cannot fully substitute for physical assessment because real fabric behaviour, seam bulk, and body movement introduce fit effects that simulation still approximates rather than reproduces exactly. Physical fit sessions bring together design, merchandising, and technical teams to review the sample on a body, checking ease at key girths, garment balance, and range of motion for functional garments.
Fit comments are recorded against specific points of measurement, with each comment classified as a pattern correction, a construction correction, or a design change, since the corrective action differs by category. A grading or fit consistency check across the sample size and adjacent sizes confirms the fit intent holds through the size range, not only on the sample size body. Sign-off at this stage is formally recorded, typically by the technical or merchandising lead, and becomes the reference point pattern development uses to close out the current sampling round. Repeated fit failures on the same points of measurement usually indicate the base pattern or block needs revision rather than a one-off correction.
How it is done
- 1Run virtual fit check
Review the 3D avatar in standard poses to flag obvious proportion, drape, or ease issues before committing to a physical sample.
- 2Set up the physical fit session
Dress the fit model or mannequin in the sample and photograph front, back, and side views for the record.
- 3Measure key points of measurement
Record actual garment measurements at each specified point and compare against the tolerance allowed in the spec sheet.
- 4Assess ease, balance, and movement
Check ease at chest, waist, and hip, garment balance front-to-back, and range of motion for functional or performance garments.
- 5Classify and log fit comments
Categorise each comment as pattern, construction, or design related, and assign the correction to the responsible team.
- 6Sign off and route to pattern update
Record formal sign-off with photos and comment sheet, then route the file to pattern development for the next revision.
Key metrics (indicative targets)
| Metric | Working target | Why it matters |
|---|---|---|
| Fit approval rate per round | Indicative: increasing round over round, reaching 90%+ by PP stage | A flat or declining approval trend signals unresolved root-cause fit issues. |
| Points of measurement within tolerance | Indicative: 95%+ of measured points within spec tolerance | Points outside tolerance drive comment volume and rework. |
| Comment classification accuracy | Indicative: correctly routed to pattern, construction, or design in 95%+ of cases | Misclassified comments send corrections to the wrong team and waste a cycle. |
| Fit session turnaround time | Indicative: within 1-2 working days of sample receipt | Delayed fit sessions push the whole sampling calendar back. |
| Recurring comment rate | Indicative: under 10% of comments repeating from a prior round | High recurrence indicates the base pattern, not just the sample, needs correction. |
Targets are indicative working ranges, not standard or legal limits.
Control points to check and sign off
- Fit session photographs and measurements are recorded and retained for each round.
- Every fit comment is classified by corrective action type before being routed onward.
- Fit consistency is checked across at least the sample size and one adjacent size.
- Formal sign-off is documented with a named approver before the sample round is closed.
- Recurring comments are escalated to a base pattern or block review rather than repeatedly patched.
Common pitfalls and their consequences
- Relying on virtual fit review alone for garments with complex drape or stretch, missing real-fabric fit problems.
- Failing to classify fit comments correctly, sending a pattern issue to the construction team and losing a cycle.
- Checking fit only on the sample size and assuming the rest of the size range fits proportionally.
- Proceeding to bulk without a documented sign-off, leaving no clear reference if a dispute arises later.
- Patching the same fit comment repeatedly without escalating to a block-level pattern review.
Main activities
- Brief interpretation and range planning
- Concept, silhouette and colour development
- Digital sampling and virtual fit sign-off
Quality risks
- Fit rejection
Sustainability risks
- Sample rework
AI opportunities
- AI fit prediction
Official sources
Learn the skills used at this stage
Free GarmentEd lessons with worked calculations, checklists and practice questions for the work described above.
Also relevant: Pattern CAD and Digital Fit, Sample Types and Approval.